Remote toggle switch circuit

Remote toggle switch circuit

Remote toggle switch circuit

Description.

In application level this circuit is similar to that of the circuit given previously. The only difference is in the approach. This circuit is designed by using another method. Using this circuit you can toggle any electrical appliance between ON and OFF states by using your TV remote. The only requirement is that your TV remote should be operating in the 38 KHz.

 

The IC1 (TSOP 1738) is used to receive the infrared signals from the remote. When no IR signal from remote is falling on IC1, its output will be high. When the IR signal from the remote falls on the IC1, its output goes low. This triggers the IC2 which is wired as a monostable multivibrator.The output of the IC2 (pin6) goes high for a time of 1S (set by the values of R2 and C3.This triggers the flip flop (IC2) and its Q output (pin 15) goes high. This switches on the transistor, which activates the relay and the appliance connected via relay is switched ON. For the next press of remote the IC1 will be again triggered which in turn makes the IC2 to toggle its output to low state. The load will be switched OFF. This cycle continues for each press of the remote. The pin 6 and pin 4 of IC1 are shorted to avoid false triggering.The diode D1 can be used as a freewheeling  diode.

Circuit diagram with Parts list.

Notes.

• Assemble the circuit on a good quality PCB or common board.
• The circuit can be powered from  a 5V DC regulated power supply.
• The capacitors must be rated 15 V.
• The IC1&IC2 must be mounted on holders.
• The current capacity  of relay determines the load circuit can switch.Use a high amperage(`10A or above) relay for driving large loads like motor,heater etc.

 

To Get this Project Contact Us or leave us an Email

At  freshersblog@gmail.com.

or Call us at 9717408885

Remote controlled appliance switch circuit

Remote controlled appliance switch circuit

 

Description.

Here is a versatile remote controlled appliance switch that can ON or OFF any appliance connected to it using a TV remote.

 

IR remote sensor IC TSOP 1738 is used for recieving the signal. Normally when no signal is falling on IC3 the output of it will be high.This makes Q1 OFF.When a signal of 38 KHz from the TV remote falls on the IC3 its output goes low.This makes Q1 conduct and a negative pulse is obtained at pin 2 of IC 1  NE 555.Due to this IC1 wired as a monostable multivibrator produces a 4 Sec  long high signal at its out put.This high out put is the clock for IC 2 which is wired as a Flipflop and of , its two outputs pin 3 goes low and pin 2 goes high.The high output at pin 2 is amplified to drive the relay .For the next signal  the outputs of IC2 toggles state. Result, we get a relay toggling on each press on the remote.Any appliance connected to this circuit can be switched ON or OFF.

Circuit Diagram with Parts List .

Notes.

• Before wiring the circuit make sure that the carrier frequency  of the TV remote you have is 38 KHz.For that wire the sensor part only ,point your remote to the TSOP1738 and press any switch.If  out put of TSOP1738  goes  low them ok, your remote is of 38Khz type.Nothing to worry almost all TV remote are of this type.
• You can use any switch because for any switch the code only changes,the carrier frequency remains same.We need this carrier frequency only.
• Assemble the circuit on a good quality PCB or common board.
• The appliance can be connected through NO or NC  and contacts of the relay .

www.indianengineer.wordpress.com

email   freshersblog@gmail.com

Go to contact us page to contact Us or leave us an email.

We Deals in Projects Kits,circuits,models,presentations,training kits,

 Wanna Buy this projects call Us. 9717408885

Low cost projects only at indianEngineer’s